background image

 

iii

 

ELEKTRISCHE—TOESTELLEN VAN KLASSE 1
DIT TOESTEL MOET GEAARD WORDEN. De stekker moet aangesloten zijn op een juist geaarde contactdoos. Een onjuist geaarde 
contactdoos kan de metalen onderdelen waarmee de gebruiker eventueel in aanraking komt onder gevaarlijke spanning stellen.

ELEKTRISCHE—SNOEREN
Gebruik een elektrisch snoer, maximum 4,5 meter lang, berekend voor ten minste 6 ampère, 250 V, uit HAR vervaardigd, met aan het ene 
uiteinde een gevormde IEC 320 stekker en aan het andere uiteinde een stekker die goedgekeurd is door het land waar het toestel zal worden 
gebruikt.

 

MONTAGE-INSTRUCTIES

 

WAARSCHUWING: Deze modellen zijn ontworpen om te werken in HORIZONTALE stand.
VERTICALE MONTAGE mag NIET UITGEVOERD WORDEN, tenzij een daartoe speciaal ontworpen Allied Telesyn chassis voor 
verticale montage wordt gebruikt.

WAARSCHUWING: De ventilatiegaten mogen niet worden gesperd en moeten de omgevingslucht ongehinderd toelaten voor afkoeling.

WAARSCHUWING: De rubberen voetjes NIET van het produkt LOSMAKEN behalve wanneer een chassis voor vertikale montage van 
Allied Telesyn wordt gebruikt.

 

BEDRIJFSTEMPERATUUR

 

De omgevingstemperatuur voor dit produkt mag niet meer bedragen dan 50 graden Celsius.

 

ALLE LANDEN:

 

 het toestel installeren overeenkomstig de lokale en nationale elektrische voorschriften.

 

ENERGIE RAYONNEE

 

Ce matériel a été testé et est certifié conforme par la réglementation américaine aux normes définies pour les appareils de classe A.

 

SECURITE

 

INFORMATION SUR L’ELECTRICITE
AVERTISSEMENT: DANGER D’ELECTROCUTION
Pour empêcher les dangers d’ELECTROCUTION, ne pas enlever le couvercle. L’équipement ne contient aucun élément réparable par 
l’utilisateur. Cet appareil comprend des TENSIONS DANGEREUSES et ne doit être ouvert que par un technicien dûment qualifié. Pour 
éviter tout risque d’ELECTROCUTION, débrancher l’appareil de la prise de courant avant de connecter ou de déconnecter les câbles LAN.

DANGER DE FOUDRE
DANGER: NE PAS MANIER l’équipement ou les CABLES pendant les périodes d’activité orageuse.

ATTENTION: LE CORDON D’ALIMENTATION SERT DE MISE HORS CIRCUIT
POUR COUPER L’ALIMENTATION DE L’APPAREIL, débranchez le cordon.

 

INSTALLATION

 

ELECTRICITE—REGLAGE DE TENSION AUTOMATIQUE
Ce produit peut s’ajuster automatiquement sur n’importe quelle tension comprise dans la plage indiquée sur le label.

ELECTRICITE—EQUIPEMENT DE CLASSE 1
CET APPAREIL DOIT ETRE MIS A LA TERRE. La prise de courant doit être branchée dans une prise femelle correctement mise à la 
terre. Sinon, des tensions dangereuses risqueraient d’atteindre les pièces métalliques accessibles à l’utilisateur.

ELECTRICITE—INFORMATION SUR LE CORDON
Utiliser un cordon secteur de 4,5 mètres de long maximum, calibré à 6 ampères minimum, 250V, et fabriqué en câblage HAR avec connecteur 
IEC 32C moulé à une extrémité et à l’autre extrémité, une prise de courant mâle répondant aux normes du pays d’utilisation.

 

INSTRUCTIONS DE MONTAGE

 

ATTENTION: Ces modèles sont destiné à fonctionner en position horizontale. L’appareil NE DOIT PAS être utilisé en MONTAGE 
VERTICAL sans employer un châssis de montage vertical Allied Telesyn conçu à cet effet.

ATTENTION: Ne pas bloquer les fentes d’aération, ce qui empêcherait l’air ambiant de circuler librement pour le refroidissement.

ATTENTION: Ne pas ôter les pattes d’attache en caoutchouc du produit, à moins d’utiliser un châssis de montage vertical Allied Telesyn.

 

TEMPERATURE DE FONCTIONNEMENT

 

Ce produit est capable de tolérer une température ambiante maximum de 50 degrés Celsius

 

POUR TOUS PAYS:

 

 Installer le produit conformément aux normes électriques nationales et locales.

 

SÄTEILYENERGIA

 

Tämä kaupallinen tuote on testattu ja noudattaa Yhdysvaltojen vaatimuksia luokan A laitteelle.

 

TURVALLISUUS

 

SÄHKÖÖN LIITTYVIÄ HUOMAUTUKSIA
VAROITUS: SÄHKÖISKUVAARA
Estääksesi SÄHKÖISKUN älä poista kantta. Sisällä ei ole käyttäjän huollettavissa olevia osia. Tämä laite sisältää VAARALLISIA 
JÄNNITTEITÄ ja sen voi avata vain koulutettu ja pätevä teknikko. Välttääksesi SÄHKÖISKUN mahdollisuuden katkaise sähkövirta 
tuotteeseen ennen kuin liität tai irrotat paikallisverkon (LAN) kaapelit.

SALAMANISKUVAARA
HENGENVAARA: ÄLÄ TYÖSKENTELE laitteiden tai KAAPELEIDEN KANSSA SALAMOINNIN AIKANA.

HUOMAUTUS: VIRTAJOHTOA KÄYTETÄÄN VIRRANKATKAISULAITTEENA. VIRTA KATKAISTAAN irrottamalla virtajohto.

Waarschuwingen

!

Avertissement

Danger

!

Attention

!

Varoitus

Hengenvaara

!

Summary of Contents for CentreCOM AT-3012T





























Reviews: