Alliance Laundry Systems BFNBCASG113TN01 Original Instructions Manual Download Page 38

Page: 38 / 51

To Exit Factory Test

To exit a test step, disconnect the machine from electrical power.

Factory Test Quick Reference Chart

Display

Test Mode

Comments

Control Type

FL is the control type.

SXXX

Software Version Number

XXX is the control version number.

Control Level

The control will display the control level
as Display 1.

drAi

PUNP

Drain Type

The control will show

drAi

if it is con-

figured for a gravity drain. It will show

PUNP

if it is configured as an electric

pump machine. The control will remain
in this mode until the Start keypad is
pressed.

HEAt

Heater Installed

The control will show

HEAt

if it is con-

figured for a Water Heater. The control
will skip this step if it is not configured
for a Water Heater. The control will re-
main in this mode until the Start keypad
is pressed.

v oP

v CL

Coin Vault Test

v oP

is displayed when coin vault

switch is open.

v CL

is displayed when

coin vault switch is closed.

S oP

S CL

Service Door Switch Test

S oP

is displayed when service door

switch is open.

S CL

is displayed when

service door switch is closed.

CXCX

Coin Drop Test

X is the number of coins entered. Coin
drop #1 is shown on the left of the dis-
play and coin drop #2 is shown on the
right of the display.

CArd

LCSU

, or

Card Reader Test

CArd

is displayed when a card reader is

completed but not driving the display.

LCSU

is displayed when a programming/

setup card is needed.

is displayed

when a programming/setup card was suc-
cessful.

PAXX

Keypad Test

XX is the number of the keypad being
pressed. You need to press all keypads to
advance to the next step.

Table 7

continues...

Testing Machine and Electronic Control Functions

DO NOT COPY or TRANSMIT

Part No. 805407R6

Summary of Contents for BFNBCASG113TN01




















































Search results

Summary of Contents for BFNBCASG113TN01

Reviews:

Related manuals for BFNBCASG113TN01

Brands by name

Popular brands

Alliance Laundry Systems BFNBCASG113TN01, Original Instructions Manual

Search results

Summary of Contents for BFNBCASG113TN01

Reviews:

Related manuals for BFNBCASG113TN01

Brands by name

Popular brands