All Safety Products Fleet Shower SH1 Series Manual Download Page 17

April 1999 

    Page 17 of 17 

Fleet Shower Model 

USE, SERVICE AND MAINTENANCE SUGGESTIONS 

WE STRONGLY SUGGEST MEMBERSHIP IN THE PORTABLE SANITATION  

ASSOCIATION INTERNATIONAL (PSAI) WHICH IS THE RECOGNIZED  

WORLDWIDE AUTHORITY ON PORTABLE SANITATION SERVICES: 

PORTABLE SANITATION ASSOCIATION INTERNATIONAL 

7800 METRO PARKWAY, SUITE 104 

BLOOMINGTON, MINNESOTA 55425 USA 

800-822-3020 / 612-854-8300 (FACSIMILE 612-854-7560) 

THE PSAI, "PORTABLE SANTATION INDUSTRY CERTIFICATION

PROGRAM" MANUAL CONTAINS A WEALTH OF INFORMATION OF  

STANDARDS AND SERVICE PROCEDURES. 

USE A MILD SOAP DETERGENT TO CLEAN ALL SURFACES AND 

COMPONENT PARTS. 

USE A DEODORANT SPRAY ON THE INSIDE SURFACES TO KEEP THE 

INSIDE SMELLING FRESH AND CLEAN. 

MINOR SCRATCHES AND ABRASIONS MAYBE LIGHTLY SANDED OR 

SCRUBBED WITH A MILD ABRASIVE CLEANER (such as "Soft N'  

Scrub"®) THAT CONTAINS CALCIUM CARBONATE, HYPOCHLORATE 

BLEACH AND DETERGENTS. 

BE SURE TO FOLLOW THE CLEANING 

PRODUCT DIRECTIONS SINCE THESE INGREDIENTS MAY CAUSE 

HAZARDOUS GASSES WHEN MIXED WITH OTHER CHEMICALS. 

RINSE 

THE CLEANED AREAS AND BUFF WITH A CONVENTIONAL WAX. 

SOME MINOR SCRATCHES MAY BE REMOVED WITH A HOT AIR GUN 

SUCH AS A CONVENTIONAL HAIR DRYER OR AN INDUSTRIAL HOT AIR 

GUN.

WHEN THE SHOWER ROOM IS NOT IN USE, ADD A SMALL AMOUNT OF 

BLEACH AND A CUP OF WATER OR A CHLORINE SANITIZER TABLET 

WITH WATER TO KEEP THE PLUMBING SYSTEM SMELLING FRESH AND 

CLEAN FOR THE NEXT USE. BE SURE TO FLUSH THE BLEACH FROM 

THE PLUMBING SYSTEM BEFORE PERSONS USE THE SHOWER ROOM. 

FOR A SOURCE OF CLEANING AND DEODORIZING PRODUCTS, PLEASE BE

SURE TO VISIT US AT WWW.ALLSAFETYPRODUCTS.COM OR CALL US AT

OUR TOLL FREE PHONE NUMBER, 1-877-208-3109. 

Summary of Contents for Fleet Shower SH1 Series


















Reviews: