ALGE-Timing TdC 8000 Manual Download Page 99

Page: 99 / 108

TdC 8000 for Equestrian

Page 99

Version: E-01-08-08

Page 99

7.2.

RS 232 Interface (16, 23)

Transfer Format:

1 start bit, 8 data bit, no parity bit, 1 stop bit

Transfer Speed:

9.600 Baud pre adjusted (adjustable: 2400, 4800, 19200)

Transfer Protocol:

ASCII

xNNNNxCCxxHH:MM:SS.zhtqxGR(CR)

time from C0 to C9

xNNNNxCCMxHH:MM:SS.zhtqxGR(CR)

manual time from <START> or <STOP> button

xNNNNxRTxxHH:MM:SS.zhtxxGR(CR)

run time

xNNNNxTTxxHH:MM:SS.zhtxxGR(CR)

total time

xNNNNxSQxxHH:MM:SS.zhtxxGR(CR)

sequential time (lap time)

xNNNNICCxxHH:MM:SS.zhtxxGR(CR)

Dual Timer, times form C0 to C9

xNNNNIRTxxHH:MM:SS.zhtxxGR(CR)

Dual Timer, run time

xNNNNiCCxxHH:MM:SS.zhtqx##(CR)

Parallelslalom, Intermediate Time or Finish Time

xNNNNiRTxxHH:MM:SS.zhtqx##(CR)

Parallelslalom, Run Time

xNNNNiDTRxHH:MM:SS.zhtxx##(CR)

Parallelslalom, Difference Time of Run

xNNNNiTTxxHH:MM:SS.zhtqx##(CR)

Parallelslalom, Total Time

xNNNNiDTTxHH:MM:SS.zhtxx##(CR)

Parallelslalom, Total Difference Time

pNNNNiCCxxHH:MM:SS.zhtqx##(CR)

Parallelslalom, Finish Time calculated form Penalty
Time

pNNNNiRTxxHH:MM:SS.zhtqx##(CR)

Parallelslalom, Run Time calculated form Penalty

Time

pNNNNiTTxxHH:MM:SS.zhtqx##(CR)

Parallelslalom, Total Time calculated form Penalty

Time

xNNNNxkmhxxxxsssss.ssxxxGR(CR)

speed measurement

xNNNNxkmhxxxxsssss.ssxxxxx(CR)

speed measurement for speed skiing

?NNNNxCCxxHH:MM:SS.zhtqxGR(CR)

illegal time

m0000xCCxxHH:MM:SS.zhtqxGR(CR)

times stopped with <MEMO>

cNNNNxCCxxHH:MM:SS.zhtqxGR(CR)

cleared time

dNNNNxCCxxHH:MM:SS.zhtqxGR(CR)

disqualified time

iNNNNxCCxxHH:MM:SS.zhtxxGR(CR)

manipulated time (<INPUT>)

xxxxxxC0xxHH:MM:SS.zhtqxGR(CR)

start time after a group start

xNHH:MM:SS.zhtxxGR(CR)

stopped countdown-time (allowed)

xNNNNxRTx-HH:MM:SS.zhtxxGR(CR)

stopped countdown-time (bellow the zero value)

nNNNN(CR)

new start number shown in finish display (8)

blank

NNNN

start number (four digits)

0000

start number 0 for times stopped with <MEMO>

Identification of the course; r (= red/right), b (= blue) or l (left) course

timing channels (c0 to c9)

CCM

manual impulse (with <START> or <STOP> from keyboard 9 or 15)

channel 0 (start)

channel 5

channel 1 (finish) C6

channel 6

channel 2

channel 7

channel 3

channel 8

channel 4

channel 9

run Time

total Time

sequential Time (lap time)

DTR

difference time of run

DTT

total difference time

kmh

speed (possible output depending on unit used: kmh, mps, mph)

countdown was stopped before it reached zero

countdown was stopped after zero

HH:MM:SS.zht

time in hours, minutes, seconds, and 1/1000 seconds

HH:MM:SS.zhtq

time in hours, minutes, seconds, and 1/10000 seconds

sssss.ss

speed for 0.00 up to 99999.99 measured in km/h in speed skiing

group (from 01 to 99, no input for groups = 00)

Summary of Contents for TdC 8000













































































































Search results

Summary of Contents for TdC 8000

Reviews:

ALGE-Timing TdC 8000, Manual, Page: 99 / 108

Search results

Summary of Contents for TdC 8000

Reviews: