manualshive.com logo in svg

ALGE-Timing TdC 8000, Manual, Page: 106 / 108

Share
Download
ALGE-Timing TdC 8000 Manual Download Page 106

TdC 8000 for Equestrian 

               

Page 106

Version:E-00-08-08

Page 106

PSIMT(CR)

Protocol of selected memory times

PSITT(CR)

Protocol of selected total times

PSIITC2(CR)

Protocol of selected intermediate times of channel C2

PSIITC3(CR)

Protocol of selected intermediate times of channel C3

PSIITC4(CR)

Protocol of selected intermediate times of channel C4

PSIITC5(CR)

Protocol of selected intermediate times of channel C5

PSIITC6(CR)

Protocol of selected intermediate times of channel C6

PSIITC7(CR)

Protocol of selected intermediate times of channel C7

PSIITC8(CR)

Protocol of selected intermediate times of channel C8

PSIITC9(CR)

Protocol of selected intermediate times of channel C9

PSIBRT(CR)

Protocol of selected run times of the blue course for Dual Timer

PSIRRT(CR)

Protocol of selected run times of the red (right) course for Dual Timer

PSILRT(CR)

Protocol of selected run times of the left course for Dual Timer

0001-0024(CR)

Start number block, e.g. form StNo. 1 to StNo. 24

0065-0073(CR)

Start number block, e.g. form StNo. 65 to StNo. 73

0105-0124(CR)

Start number block, e.g. form StNo. 105 to StNo. 124

0000-0000(CR)

Finish with this input

7.3.

RS 485 Interface (16, 23, 28):

no function

Transfer Speed:

30 kBaud

Pin Arrangement:

see page 121

7.4.

Display Board Interface (24)

Transfer Format: 1 start bit, 8 data bit, no parity bit, 1 stop bit
Transfer Speed:

2.400 Baud (adjustable 4.800, 9600, 19200 Baud)

Transfer Protocol: ASCII

The display board interface has two different channels:

Channel 1: running time
Channel 2: running time and classement or run time and classement

Attention:

Switch between channel 1 and channel 2 by turning the plug of socket (24) 180°.

Channel 1 has always the same output as shown in display 7 and 8. The adjusted display time (see
menu 4 on page 52) is always valid for display 7 and 8 and channel 1 of the display board interface
(24). Channel 1 does not output a classement.

You can switch channel 2 in the main menu (menu 19 on page 56) between running and standing
time (run time). On channel 2 you have always an output of the classement.

NNN.xxxxxxxxM:SSxxxx(CR)

running time (without 1/10 seconds)

NNN.xxxxHH:MM:SSxxxx(CR)

running time (without 1/10 seconds)

NNN.xxxxHH:MM:SS.zxx(CR)

running time (with 1/10 seconds)

NNNCxxxxHH:MM:SS.zhtRR(CR)

channel C1, run time with rank

NNNCxxxxHH:MM:SS.zhtxx(CR)

channel C1, run time without rank

NNNDxxxxHH:MM:SS.zhtRR(CR)

channel C1, total time with rank

NNNDxxxxHH:MM:SS.zhtxx(CR)

channel C1, total time without rank

NNNAxxxxHH:MM:SS.zhtRR(CR)

channel C2, intermediate time 1

Summary of Contents for TdC 8000













































































































Reviews:

No comments