manualshive.com logo in svg

ALGE-Timing TdC 8000, Manual, Page: 36 / 108

Share
Download
ALGE-Timing TdC 8000 Manual Download Page 36

TdC 8000 for Equestrian 

               

Page 36

Version:E-00-08-08

Page 36

Change Heat:

Menu 24: CHANGE HEAT

You do not have to turn the TdC 8000 off to switch form one heat (e.g. heat 1) to the next heat (e.g.
heat 2).

Menu 24: Select Heat           SAME (1)< F1

Continue in the same heat

                               NEXT (2)  F2

Select a new heat

Save with: ENTER

Confirm with <ENTER>

You can select if you want to continue in the same heat or if you want to continue in the next heat.

Attention:

When you select the next heat, it is impossible to switch back to the previous heat.

Change Race Race:

Menu 25: CHANGE RACE

You do not have to turn the TdC 8000 off to switch form one race to another.

If you press <YES> or <ENTER> you can select automatically the race. You will see the same
selection as you have when you turn the TdC 8000 on. If you change a race within the menu you do
not have to make a new synchronisation.

Display Board Test:

Menu 26: D-BOARD-TEST = OFF

In this menu you can check the display board or write on the board the time of day, ALGE or blank.
If you have digits that do not work as they should, use this test to check them. Use the test <F4>
especially if you use the display board the first time after a long time or if you have very could
weather (frozen segments).

With <F1>, <F2>, <F3>, or <F4> you can select the test mode. The arrow at the right end of the
display shows the selected test. There are all together 7 display possibilities. To leave the display
board test press <ENTER>.

Menu 26: D-BOARD-TEST              TIME< F1

Shows time of day

                                   ALGE  F2

Shows ALGE

                                  BLANK  F3

Blanks the board

Continue: ENTER               123456789  F4

All 9 possible digit get a number

Menu 26: D-BOARD-TEST         123456789< F1

                              0          F2

Each digit counts up

                              8          F3

Each digit shows 8 and blank

Continue: ENTER               888888888  F4

All digits show 8 and blank

TIME It shows the time of day on the display board. With the arrow-keys you can move the time to
the correct position. Exit with <ENTER>.
ALGE It shows ALGE on the display board. With the arrow-keys you can move the time to the
correct position. Exit with <ENTER>.
BLANK

It blanks the display board. Exit with <ENTER>.

123456789 Each digit shows its position number. Exit with <ENTER>.
0

Each single digit counts form 0 to 9.  Exit with <ENTER>.

8

Each single digit switch between blank and 8.  Exit with <ENTER>.

888888888 All digits switch between blank and 8.  Exit with <ENTER>.

Pre adjusted value:

    GAZ-Test is not active

Summary of Contents for TdC 8000













































































































Reviews:

No comments