manualshive.com logo in svg

AlfaRadio AlfaSpid MD-01, Manual

Share
Download
AlfaRadio AlfaSpid MD-01 Manual Download Page 46

Alfa Radio Ltd.

11211 - 154 St. Edmonton, Alberta, Canada T5M 1X8

[email protected]

   780-466-5779   

www.alfaradio.ca

Fill in the “Static IP Address” “Subnet Mask” and “Default Gateway” to match
the network to which the controller will be connected.  Click on the “Update
Settings” button to save the new settings.

Reset the MD-01/02 controller by cycling the power off then on.

7.3 Ethernet Board Firmware Update

To update the firmware on the Ethernet Board, first download the Ethernet 
Manager program (KT-ETH-Manager-1.2.zip) from the 

A

lfa Radio Ltd. website.  

Unzip the executable and install it on your windows computer.

Then download the latest firmware (kt-eth-uart-1-v106-eng.zip) from the 

A

lfa

Radio Ltd. website and unzip the file into a convenient directory.

Connect the controller and the Windows computer to an Ethernet LAN.

Start the ETH-Manager program:

Page  46 of 55  AlfaSpid_MD-01-02_12APR2022.odt 

Copyright 

Alfa Radio Ltd.  2022

Summary of Contents for AlfaSpid MD-01
























































Reviews:

No comments

Brands by name

Popular brands

Load more brands