Alcatel-Lucent 9764 Compact Metro Cell Outdoor B3, Manual, Page: 88 / 112

Share

Page: 88 / 112

Alcatel-Lucent 9764 Compact Metro Cell Outdoor B3 Manual Download Page 88

....................................................................................................................................................................................................................................

5-9

Alcatel-Lucent – Proprietary

Use pursuant to applicable agreements

Cabling

....................................................................................................................................................................................................................................

Before you begin

Ensure that the following tools are available:



Adjustable (crescent) wrenches



Torque ratchet (socket wrench)



Items such as crimping tools that are appropriate for attaching a new cable connector
to the GPS cable



Protective eye wear

Important!

Do not mount the GPS antenna within 10 feet (3 m) of any transmit

antenna.

Safety statements

WARNING

Fall hazard

Falls can occur when working at heights resulting in serious personal injury or death.

To prevent a fall when working at heights (ladder, scaffold, manlift, roof etc.) follow safe
work practices and wear appropriate fall protection equipment.

«
...
86
87
88
89
90
...
»

Summary of Contents for 9764 Compact Metro Cell Outdoor B3

















































































































Reviews:

No comments