Alcatel-Lucent 9764 Compact Metro Cell Outdoor B3, Manual, Page: 44 / 112

Share

Page: 44 / 112

Alcatel-Lucent 9764 Compact Metro Cell Outdoor B3 Manual Download Page 44

....................................................................................................................................................................................................................................

3-5

Alcatel-Lucent – Proprietary

Use pursuant to applicable agreements

Pre-installation

Pole mount installation requirements

....................................................................................................................................................................................................................................

Pole mount installation requirements

Purpose

This topic outlines the basic requirements, installation kits and recommended anchor
materials when mounting the Alcatel-Lucent 9764 Compact Metro Cell Outdoor directly
onto a pole, onto tilt brackets or onto a pair mount bracket.

Pole mount options

The 9764 CMCO can be easily mounted onto a pole for the following installation options:



9764 CMCO banded onto a pole (without the tilt option).

The 9764 CMCO mounting bracket and pole band installation kit is used.



9764 CMCO attached to the vertical tilt bracket. Vertical tilt bracket is banded onto a
pole.

The vertical tilt bracket, 9764 CMCO mounting bracket and pole band installation kit
is used.

Pole mount installation kits and brackets

The following table provides the installation kits and brackets that can be used, depending
on the deployment scenario, for 9764 CMCO pole mounting.

Table 3-2 Pole mount installation kits and brackets

Item

Description

9764 MCO Compact mounting bracket

Required for attaching the 9764 CMCO directly onto a pole or vertical tilt
bracket

Vertical tilt bracket

Pr/- 30° vertical tilt (up/down) adjustment

Banding kit

Required when directly attaching the 9764 CMCO or vertical tilt bracket

to a pole (diameter 50 to 300 mm) using stainless steel bands.

Stainless steel bands and buckles (Ear-Lokt)

Banding tool

Standard BAND-IT

®

Banding Tool (CR00169), including operating

instructions

Required in order to tighten stainless steel metal bands

The following figure shows the brackets used for pole mount installation, depending on
the deployment scenario.

«
...
42
43
44
45
46
...
»

Summary of Contents for 9764 Compact Metro Cell Outdoor B3

















































































































Reviews:

No comments