3
Instructions for operation
English
Uso Vasche IDROP / DIGIT - Code 10004904 - Edition 3 - 09/2007
5
15'
P
P
A'
A
A
c
d
6
Led-Liv
Led-Liv
D
blood
fl
ow towards the heart, stimulates the
nerve centres, provides a relaxing effect.
c)
Air supply to nozzles in lateral and back areas
open:
Massages the back and sides
: stimulates
the circulation, acts on the lymphatic system,
helping to eliminate toxins, thus reducing
cellulite.
d)
Air supply to all nozzles open:
Complete hydromassage
: helps relieve
accumulated tension and re-charges the
body with positive energy.
Alternatively, by leaving this feature in operation,
you can enjoy an intense lymph drainage effect in
which the intensity and the sequence of operation
of the jets vary automatically in a programmed
sequence.
The sequence starts from the area of the feet, then
moves upwards until it reaches the shoulders,
eliminating toxins and relieving tension. The effect
is similar to that of a massage from the hands of
a trained masseur.
Timer
The tub also features a timer which automatically
stops the hydromassage cycle after 15 minutes.
For digital systems, the duration of the cycle can
be preset when installing the tub (see Installation
Manual).
Starting and stopping the hydromassage
cycle
To start or stop the hydromassage cycle, press
“
P
”. The cycle, which can be interrupted manually
at any time by pressing “
P
” again, is interrupted
automatically after 15 minutes.
To prolong the cycle, press “
P
” again.
Idropool systems
To select an even more personalized
hydromassage, for tubs with the pneumatic
control system, you can use knobs
A
and
A
ʼ
to adjust the quantity of air delivered by the
hydromassage nozzles.
Digit and Digit Professional systems
In tubs with digital control systems, use key
“
A
” to select the nozzles through which air is
injected.
If this device is left in operation, the jets vary in
intensity in the sequence shown in the
fi
gure
below (
a, b, c, d
).
Disinfection cycle
Tubs with digital controls can be
fi
tted with either
the System Clean or Professional disinfection
systems.
Whichever of these two systems is installed, the
disinfection cycle ensures maximum hygiene and
prolongs the life of the hydromassage circuit by
cleaning the internal parts that cannot be reached
during normal cleaning.
The System Clean disinfection system allows
you to re-use the water from the previous
hydromassage cycle. The cycle can be started
only when the tub is full.
For the Professional disinfection cycle, the tub
must
fi
rst be drained, since the system uses
cold water taken directly from the mains supply
and mixes this with the disinfectant solution to
sanitize the hydromassage circuits.
Before starting the disinfection cycle (whether
System Clean or Professional), ensure that the
tub is not in use and that all the nozzles are fully
open. The disinfection cycle lasts for two minutes
and, once started, cannot be interrupted.
Filling the disinfectant reservoir
To
fi
ll the disinfectant reservoir, remove the cap
located on the lip of the tub and introduce 1
litre of disinfectant. (LED “
Dis
” on the keyboard
changes from red to green).
Each disinfection cycle requires approximately
70 gr of disinfectant (this quantity cannot be
modi
fi
ed). A full reservoir, therefore, is suf
fi
cient
for about 10/12 cycles. A level sensor inside the
reservoir checks that it contains disinfectant; if
not, the cycle cannot be started.
The recommended disinfectant solution, which
is available through our authorized dealers and
Service Centres, not only sanitizes the appliance,
but also prevents fermentation and unpleasant
odours, and inhibits the formation of algae and
mildew.
IMPORTANT!
Do not use products containing chlorine
(Amuchina, Bleach etc.) as these may
damage the system and cause leakage of
disinfectant.
Starting the disinfection cycle
Before starting:
1) Check that the main switch is closed (in
position “I - ON”).
2) For System Clean disinfection systems,
check that the level of water in the tub is
5 cm above the nozzles (LED “
Liv
” on the
keyboard should light
green
).
For Professional systems, check that the tub is
empty (the LED on the keyboard lights
red
).
The cycle cannot be started if the disinfectant
reservoir is empty. In this case, LED “
Dis
” on
the digital keyboard lights
red
.
Press and hold down key “
D
” until LED “
D
” lights,
then release and press again within
fi
ve seconds
to start the cycle. If this key is not pressed again
within
fi
ve seconds, the cycle will not start; this
is a safety feature designed to ensure that the
Summary of Contents for Kellia Combi 170
Page 6: ......
