Alarm Lock Trilogy ETPL Programming Instructions Manual Download Page 4

Page: 4 / 28

AL-DTM - Data Transfer Module

The enhanced

AL-DTM

may be used to transfer program data between a PC running DL-Windows

software and locks. Use of the older

AL-DTM

model 1

is not recommended.

Prox Card Reader/Enroller

(AL-PRE)

AL-PRE

is used to quickly enroll multiple ProxCards

and ProxKey

keyfobs into DL-Windows. Use the

supplied 9-pin DB9 to DB9 serial cable to connect the AL-PRE to your computer’s serial COM port. Compatible
with most HID ProxCards

and ProxKey

keyfobs (37 bits or less). For PDL and PL series locks only.

H ID

HID CORPORATION

ProxCard

/ ProxKey

Keyfob

Compatible with most HID ProxCards

and ProxKey

keyfobs (37 bits or less).

Note:

ProxCard

and ProxKey

are trademarks of

the HID

Corporation.

Double-ended Mini Banana Plug Connector

After you create the program in DL-Windows and transfer the program from your computer to an

AL-DTM

transfer the program from the

AL-DTM

to the lock(s) via a double-ended mini banana plug. You can also

use this cable to transfer the Lock Program from your lock to an AL-PRE.

DB9 to DB9 Serial Cable

Enroll ProxCards quickly into DL-Windows, then transfer this new ProxCard

data from the computer to

the

AL-PRE

via this 9-pin DB9 to DB9 serial cable. Once the data is in the

AL-PRE

, you can transfer the

data to the lock via the double-ended mini banana plug (see above), thus avoiding the need to use an

AL-

PCI2

cable for this process.

AL-PCI2 Cable

An ALARM LOCK

AL-PCI2

cable is required to communicate between your computer’s RS-232 serial com-

munications port (COM 1-4) and the

AL-DTM

or lock. One end of the

AL-PCI2

cable is designed to be used

on a 9-pin serial Com Port. If your computer has a 25-pin Com Port only, a 25-pin to 9-pin adapter must be
used. The other end of the

AL-PCI2

cable features a 2-pin banana plug connector which is polarity sensi-

tive--the TAB (marked “GND”) side must be plugged into the lock’s

black

(left) terminal.

Supported Products

Infrared Printer (AL-IR1)

AL-IR1

printer is used to print Audit Trails

without the need for a PC. Its infrared reader
means no cable connection to the lock is
needed.

Summary of Contents for Trilogy ETPL





























Search results

Summary of Contents for Trilogy ETPL

Reviews:

Related manuals for Trilogy ETPL

Brands by name

Popular brands

Alarm Lock Trilogy ETPL, Programming Instructions Manual

Search results

Summary of Contents for Trilogy ETPL

Reviews:

Related manuals for Trilogy ETPL

Brands by name

Popular brands