AL-MEISTER ALM3222 Instruction Manual Download Page 49 | Manualshive

Page: 49 / 52

background image

AL-MEISTER ALM3222 Instruction Manual <Rev.2>

Page

49

of

52

compatibility problem.

More than 1-1/4”of paper is
fed. Paper is very thin.

Remove  the  paper. Slightly  lower
the  position  of  Feeding  Pressure
Knob. Ruffle  the  papers  well.
Flatten the  papers.  Press  RESET
button.

Paper is fed on the bias
direction.

Remove paper. Widen Paper
Guide a little. Press RESET
button.

The surface of Feeding Rollers
is not clean.

Remove  paper. Open  Feeder
Cover. Wipe  off  the  stains  on  the
Feed  Roller  with  soft cloth. Press
RESET button.

●PAPER JAM

Paper

is

stuck

between

feeding section and lamination
section.

Open Feeder Cover. Remove all
the stuck paper. Press RESET
button. CAUTION:

The lamination

rollers get very hot.

●DISCHARGE ERROR

Laminated paper is stuck at
Cutter section or Trimmer
section.

Follow the instruction for the problem

:●Laminated sheet is not discharged,
page.34.

The already laminated film has
a curl.

[1]  Press  RESET  button. [2]  Cut
the  upper  and  lower film  between
heat  shoe  and  guide roll. Press
Manual

Feed

Switch to

BACKWARD. Remove  the  film
and  paper. Follow  the  “Before
Starting  Lamination”  to  adjust  the
film curl.

●LAMINATION ERROR

Paper is stuck in Lamination
section or Cutter section.

[1] Follow the instruction for the
problem

:●Laminated sheet is not

discharged, page.31. Remove the
film  or  laminated sheet  in  the
machine. [2]  In  case  the  paper  is
stuck  in the  feeder  tray,  pull  out
the  paper  carefully.  When  the
error  is  not  solved, switch  off  and
contact  your dealer  or  distributor.
CAUTION: T

he lamination rollers

get  very  hot.  Be  careful  that  your
fingers  or  clothes  do  not  get
caught  in  the  rollers.  Be  careful
that your  fingers do not  get cut. Do
not  dismantle.

Lamination scrap is stuck in
the trimmer section.

Open trimmer Cover. Remove all
the

lamination

scrap.

Press

RESET button.

Be careful that

your fingers do not get cut.

Operation lever is in the OPEN
position.

Lamination Handle to LAMINATE
position. Press RESET button to
clear error

●LAMINATION ERROR

Roll film has run out.

Remove the film roll. Press
RESET button to clear error. Load

«
...
47
48
49
50
51
...
»

Summary of Contents for ALM3222





















































Reviews:

No comments

Related manuals for ALM3222

Brand: GBC Pages: 35

Brand: GBC Pages: 54

Pro-Tech NORD ORCA-I SP

Brand: GBC Pages: 60

Brand: GBC Pages: 72

Brand: Lapis Pages: 42

Brand: Xyron Pages: 10

Brand: EMBLEM Pages: 20

Brand: Clas Ohlson Pages: 4

Brand: Clas Ohlson Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands