Airspan MicroMAX Hardware Installation And User'S Manual Download Page 72

Page: 72 / 100

MicroMAX Hardware Installation User Guide

Page 72

Commercial in Confidence

UWB-D00068 Rev J

16 Connecting BSDU to AC/DC Power converter

This section provides a description of how to connect the

Base Station Distribution Unit

(BSDU)

to the external

AC/DC Power

converter. This section explains the steps needed to connect the

two units together for proper functioning.

Table 26 - Required Equipment

Equipment Description

Part number

BSDU MMX-BSDU-1

AC/DC Converter

PC-BSDU-1

BSDU to AC/DC Converter Cable 68000110

BSDU to DC power Supply Cable supplied with BSDU kit

16.1 Connections

There are two sets of cables required for the BSDU and AC/DC converter to work properly.

Cable with 25-pin D-type Male to 25-pin D-Type Male (part no. 68000110) with 2 cables

(UL 20AWG red color and UL 20AWG black color both with ring terminals).

Figure 57 - BSDU - AC/DC cable

Note:

This cable connects between the rear panels of the BSDU and the

AC/DC converter. It also has connections to the main DC Output of the
AC/DC converter, but the cable itself

DOES NOT

carry power to the BSDU.

These connections are used for sensing purposes, so that the PSU can
adjust the DC output according to the load drawn by the BSDU.

Summary of Contents for MicroMAX





































































































Search results

Summary of Contents for MicroMAX

Reviews:

Brands by name

Popular brands

Airspan MicroMAX, Hardware Installation And User'S Manual

Search results

Summary of Contents for MicroMAX

Reviews:

Brands by name

Popular brands