manualshive.com logo in svg

Airspan MicroMAX, Hardware Installation And User'S Manual

Share
Download
Airspan MicroMAX Hardware Installation And User'S Manual Download Page 27

                                

MicroMAX Hardware Installation User Guide

 

 

 

 
Page 27 

Commercial in Confidence 

UWB-D00068 Rev J 

 

 

4.3.2 Ports 

The SDA-4SDC adapter provides ports on the front panel, which are described in the table below: 

Table 8 - SDA-4SDC ports 

Port 

Interface 

4 x 8-pin RJ-
45 

10/100BaseT with subscriber's network (supports Auto Negotiation and 
MDI/MDI-X automatic crossover, allowing connection of straight-through or 
crossover cables) 

15-pin D-type 
(female) 

10/100BaseT with BSR 

DC power 
socket 

DC power outlet (10-52 VDC, 24W) 

4.3.3 LEDs 

The SDA-4S (all types) adapter provides LED indicators on the top panel, which are described in 
the table below: 

Table 9 - SDA-4S LEDs 

LED 

Color 

Status 

Description 

On 

Physical link (10BaseT or 100BaseT) 
between SDA-4S adapter and BSR 

Blinking 

Traffic currently flowing between SDA-4S and 
BSR 

UPLINK 

Yellow

 (100BaseT) or 

Orange

 (10BaseT) 

Off 

No link between SDA-4S and BSR 

On 

Physical link (10BaseT or 100BaseT) 
between SDA-4S and subscriber's Ethernet 
network 

Blinking 

Traffic currently flowing between SDA-4S and 
subscriber's Ethernet network 

1, 2, 3, 
4 

Yellow

 (100BaseT) or 

Orange

 (10BaseT) 

Off 

No link between SDA-4S and subscriber's 
Ethernet network 

On 

Power received by SDA-4S 

POWER Green 

Off 

No power received by SDA-4S 

 

The figure below displays the LEDs which are located on the top panel of the SDA-4S adapter: 

Summary of Contents for MicroMAX





































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands