manualshive.com logo in svg

Airspan MicroMAX, Hardware Installation And User'S Manual

Share
Download
Airspan MicroMAX Hardware Installation And User'S Manual Download Page 29

                                

MicroMAX Hardware Installation User Guide

 

 

 

 
Page 29 

Commercial in Confidence 

UWB-D00068 Rev J 

 

 

5 BSDU 

Description 

This section provides a description of the 

Base Station Distribution Unit

 (BSDU).  

The BSDU is connected to the BSRs by standard CAT-5e cables. Each BSDU can service a 
maximum of 8 BSRs. In addition, up to two BSDUs can be daisy-chained at a Base Station, 
supporting up to 16 BSRs. Therefore, a Base Station at maximum configuration can serve up to 
8192 subscribers (i.e. 16 BSRs multiplied by 512 subscribers). 

The BSDU provides a 15-pin D-type port for interfacing with the BSRs, for convenience, a DB15-
to-RJ45 adapter is supplied for attaching to the 15-pin D-type port to allow the use of RJ-45 
connectors for outdoor-to-indoor CAT-5e cable connectivity.  

The AIRSPAN WIMAX Base Station Distribution Unit (BSDU) provides an interface between 
multiple MicroMAX (BSRs) and the service provider’s backbone. The BSDU provides the 
following functionalities: 

¾

  Data switching and aggregation:  

•

  Data switching between up to eight MicroMAX BSRs over 10/100 BaseT interface. 

•

  Aggregate the MicroMAX BSRs data via two 1000BaseT Ethernet (GE) ports towards 

the backhaul/backbone or to cascade to another BSDU. 

¾

 Synchronization: 

 

•

  Tx / Rx TDD synchronization for multiple MicroMAX BSRs per BSDU and between 

connected BSDUs. 

•

  GPS for TDD Tx / Rx synchronization of different BS sites. 

¾

 Power 

distribution 

•

  Provides DC power from a single -48 VDC source to eight MicroMAX BSRs. 

•

  AC/DC power converter (optional) - in the event -48 VDC is not available at BS site. 

 

Note:  

The unit should be powered by -48Vdc (40-54Vdc), 4.5A from safety 

approved power supply that its output is SELV and is separated from mains 
by minimum double/reinforced insulation. 

5.1  Physical Dimensions 

The table below lists the physical dimensions of the BSDU. 

Table 10 - BSDU dimensions 

Parameter Value 

Comment 

Height 

43.2 mm (1.7 inches) 

Width 

482.6 mm (19 inches) 

Depth 

228.6 mm (9 inches) 

Weight 2.9 

kg 

 

The physical dimensions exclude the bracket flanges for mounting.

 

The figure below illustrates the BSDU's physical dimensions. 

Summary of Contents for MicroMAX





































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands