manualshive.com logo in svg

Airspan MicroMAX, Hardware Installation And User'S Manual

Share
Download
Airspan MicroMAX Hardware Installation And User'S Manual Download Page 67

                                

MicroMAX Hardware Installation User Guide

 

 

 

 
Page 67 

Commercial in Confidence 

UWB-D00068 Rev J 

 

 

14  Connecting the SDA-4S to the power supply 

14.1 Connecting the SDA-4S Type II 

The SDA-4S adapter is plugged into a standard electrical wall outlet (110/240 VAC) using an AC 
power cord. The appropriate AC power cord is supplied according to the country of use. 

The cable setup between the SDA-4S and power outlet includes the following: 

¾

 

Connector:

 AC IEC 60320 type (female) 

¾

 

Plug:

 The appropriate plug type is supplied according to the country of use 

¾

 

Cable:

 3x1.z0 mm, 10A / 250 VAC (maximum length is 180 cm) 

 

Figure 49 - Power chord 

To connect the SDA-4S to the AC power supply: 

1.  Connect the power plug female, at the end of the AC power chord, into the AC power socket 

located on the left panel of the SDA-4S. 

2.  Plug the power plug male, at the other end of the AC power chord, into the AC power outlet 

(110-240 VAC). 

3.  Verify that the power is received by the SDA-4S by checking that the 

POWER

 LED light is 

on. 

Summary of Contents for MicroMAX





































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands