manualshive.com logo in svg

Airspan MicroMAX, Hardware Installation And User'S Manual

Share
Download
Airspan MicroMAX Hardware Installation And User'S Manual Download Page 53

                                

MicroMAX Hardware Installation User Guide

 

 

 

 
Page 53 

Commercial in Confidence 

UWB-D00068 Rev J 

 

 

To wall mount the SDA-4S: 

On the wall, mark the position of the two mounting hooks. The dimensions of the wall-mounting 
hooks are displayed in the template below. 

 

Figure 38 - SDA-4S mounting template 

6.  Drill holes for each hole that you marked in the step above. 

7.  Insert wall anchors (supplied) into each of the drilled holes. 

8.  Insert the 9-inch screws (supplied) into the wall anchors. Ensure at least 2 mm of the screw 

is exposed to allow insertion into the SDA-4S mounting holes. 

9.  Hold the SDA-4S with both hands, and align the entrance to the two mounting hooks with the 

screws. Slide the screws into the mounting hooks, by lowering the SDA-4S onto the screws. 

 

Note:

 For safety, both mounting hooks must be utilized when mounting the 

unit. 

 

 

Note:

 The SDA-4S is supplied with a 1-metre AC power lead assembly. 

Therefore, ensure the unit is mounted within reachable distance to the 
customer's mains power outlet. 

 

 

Note:

 The maximum cable run between SDA-4S and MicroMAX is 100 

meters. Therefore, ensure the unit is mounted within reachable distance. 

 

Summary of Contents for MicroMAX





































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands