Airspan AirSynergy3 Installation Manual Download Page 65

Page: 65 / 65

AirSynergy3 Equipment Installation Guide

Page 65 | Commercial in Confidence SYN-UG-018

Revision

Originator

Date

Description

Customer Service Help-Desk for customer service emergency

Airspan Networks have introduced the Airspan Tracker application to enable prompt and efficient
Customer Support services.

If you do not have an Airspan Tracker account, please obtain login credentials by filling-in the form in
the main page at www.airspan.com/Support Register New Account.

Worldwide Headquarters:

Airspan Networks Inc.

777, Yamato Road, Suite 310,

Boca Raton, FL 33431, USA

Tel: +1 561 893 8670

www.airspan.com

Feedback:

To provide feedback on this document, please send comments to the following email

address:

[email protected]

Summary of Contents for AirSynergy3


































































Search results

Summary of Contents for AirSynergy3

Reviews:

Related manuals for AirSynergy3

Brands by name

Popular brands

Airspan AirSynergy3, Installation Manual

Search results

Summary of Contents for AirSynergy3

Reviews:

Related manuals for AirSynergy3

Brands by name

Popular brands