manualshive.com logo in svg

Airspan AirSynergy3, Installation Manual

Share
Download
Airspan AirSynergy3 Installation Manual Download Page 32

                                 

AirSynergy3 Equipment Installation Guide

 

Page 32 |                                     Commercial in Confidence                                           SYN-UG-018 

 

 

Figure 38 – AirSynergy  antenna connections – applying PVC tape 

Ensure the RF connector is completely sealed from the weather. 

 

 

4.3  Connect Power drop cable to the AirSynergy 

4.3.1 Plan the position of the drop cable run from the AirSynergy unit to the Power supply. The 
standard cable supplied provides for a run length of 30m. (For run lengths greater than 30m please 
consult Airspan Product Management). 

Uncoil the cable and secure with the connector hood just below the AirSynergy unit.  When securing 
the cable, make sure that there is no tension on the connector so that it is easy to disconnect and re-
connect for maintenance activities in the future. With the pins correctly located, the connector is 
secured to the unit with a locking ring that is screwed into place. Use firm hand pressure only, the 
connector has a built in sealing ring. 

 

 

Caution:  

The internal plastic parts of the mating connector are keyed. Take care 

to align these by visual inspection or by gently rotating the connector body until 
the key way sections align and the pins go in before tightening the locking ring. 

 
 

 

Figure 39 – Attach the power cable to the AirSynergy 

Summary of Contents for AirSynergy3


































































Reviews:

No comments

Brands by name

Popular brands

Load more brands