Airspan AirSynergy3 Installation Manual Download Page 56 | Manualshive

Page: 56 / 65

background image

AirSynergy3 Equipment Installation Guide

Page 56 | Commercial in Confidence SYN-UG-018

10 Appendix E

– PSU for USA

To comply with US regulations that apply to outdoor deployments of mains power supplies, a special
US version of the AirSynergy power supply has been produced with the PSU module and the mains
connecting blocks enclosed in a small NEMA approved enclosure. The mains cable and 48V power
cables are brought through the weatherproof glands provided. This type of power supply (SYN-PSU-
ODUL-AC-1) must be used for all deployments in the USA.

Figure 71

– AirSynergy Mains PSU and enclosure for USA deployments

Remove the top cover of the PSU enclosure. Choose suitable positions for the PSU enclosure. The
PSU enclosure should be screwed to a firm surface with screws in 4 positions which are only
accessible with the top cover removed.

Figure 72

– Internal PSU and and cable terminations

Feed the Synergy3 drop cable through the gland nearest to the low voltage connection and connect to
the terminal strip, observing the correct polarity. (Blue wire in drop cable to negative terminal and
Black wire in the drop cable to positive)

«
...
54
55
56
57
58
...
»

Summary of Contents for AirSynergy3


































































Reviews:

No comments

Related manuals for AirSynergy3

Brand: CAME Pages: 4

Brand: JCG Pages: 3

Brand: LORD Pages: 9

NI WLS/ENET-9163

Brand: National Instruments Pages: 36

Brand: insys icom Pages: 4

SLK-R602 Series

Brand: Seriallink Pages: 29

EK-Quantum Momentum ROG Rampage VI Encore

Brand: EK Pages: 11

Brand: Z-Com Pages: 18

Brand: Isee Pages: 68

Elinx EIR510 Series

Brand: B&B Electronics Pages: 2

Brand: Casablanca Pages: 13

Brand: SilverStone Pages: 28

NetCon FBR-1409TX

Brand: LevelOne Pages: 88

Brand: Neousys Technology Pages: 24

Brand: AES Pages: 44

Brand: Cypress Semiconductor Pages: 38

Kontron CP3005 Series

Brand: S&T Pages: 115

Brand: Firetide Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands