manualshive.com logo in svg

Airspan AirSynergy3, Installation Manual

Share
Download
Airspan AirSynergy3 Installation Manual Download Page 42

                                 

AirSynergy3 Equipment Installation Guide

 

Page 42 |                                     Commercial in Confidence                                           SYN-UG-018 

 

 

Figure 58- Mgmt IP Config 
 
 

6. 

Click 

Submit

 

 

 

Note: 

Dynamic” IP Allocation is not supported in the current release. Please 

select Static

 

Note:

 

Internal Port configuration is not applicable to 16e BS and must not be 

used.  Configuration of the internal port may lead to management comms failure. 
 

Note:

 

Clicking the “Submit” your configuration is NOT implemented immediately 

in the BS. The BS needs to be rebooted for the new configuration to be applied.

 

 

 

 

 

 

7. 

Navigate to “

Reboot” 

and click on “Yes” to reboot the BS 

Choose Untagged or Modify the BS 
Management VLAN when applicable  

(Take care when changing to a 
management VLAN since 
communication from a Laptop or PC 
without the relevant 802.1Q NIC 
capability and configuration will be 
lost) 

Modify the BS IP 
IPIP 

Summary of Contents for AirSynergy3


































































Reviews:

No comments

Brands by name

Popular brands

Load more brands