Airspan AirSynergy3 Installation Manual Download Page 48

Page: 48 / 65

AirSynergy3 Equipment Installation Guide

Page 48 | Commercial in Confidence SYN-UG-018

Netmask:

Should only be set if Management IP Mode is set to Static IP Address. See

below for Management IP Mode parameter.

Default Gateway:

Should only be set if Management IP Mode is set to Static IP

Address. See below for Management IP Mode parameter.

Management VLAN:

Specified as either Untagged or Tagged

Management VLAN Tag:

Should only be set if Management VLAN is set to Tagged

Management IP Mode:

Specified as Static IP Address or Obtain IP Address via DHCP

Ethernet Mode:

Specified as Auto-negotiate or Fixed

Ethernet Rate:

Need only be configured if Ethernet Mode is set to Fixed, specified as

10M or 100M.

Ethernet Duplex:

Need only be configured if Ethernet Mode is set to Fixed, specified as

Full or Half.



SNMP configuration information

. This will allow events from the BS to arrive at the

specified Netspan server. This will include the following information:

Read Only Community

: This should be specified to the same value as in Netspan

Discovery Parameters (found under Server on N

etspan’s left hand panel).

Read Write Community

: This should be specified to the same value as in Netspan

Discovery Parameters (found under "Server" on Netspan’s left hand panel).

Community:

Normally specified to the same value as for Read Only Community.

Summary of Contents for AirSynergy3


































































Search results

Summary of Contents for AirSynergy3

Reviews:

Related manuals for AirSynergy3

Brands by name

Popular brands

Airspan AirSynergy3, Installation Manual

Search results

Summary of Contents for AirSynergy3

Reviews:

Related manuals for AirSynergy3

Brands by name

Popular brands