Airspan AirHarmony-1000 Installation Manual Download Page 60

Page: 60 / 62

AirHarmony-1000 Installation Guide

UGD-D01006

Airspan Commercial and Internal Use

B Checklist

During installation, review and perform all the steps on this checklist (in the given order). This
checklist is meant for the person who performs the AirHarmony-1000 installation. It includes the high

–

level steps involved in the installation process.

Tip:

To make sure you complete all the tasks, detach or print this checklist and use it as a job aid.

After performing, check off each task.

Procedure

Action

Check If Performed

Verify the prerequisites

Verify the site requirements.

☐

Verify the installation requirements.

☐

Verify the tool requirements.

☐

Verify the parts & kits required.

☐

AirHarmony-1000
installation

Install the mounting bracket.

☐

Install AC/DC converter on mounting bracket (if
required)

☐

Install AirHarmony-1000 on the mounting
bracket.

☐

Connect & manage
Cables

Connect to copper Ethernet (if applicable)

☐

Connect the fiber Ethernet (if applicable)

☐

Connect power system

Connect power

☐

Summary of Contents for AirHarmony-1000































































Search results

Summary of Contents for AirHarmony-1000

Reviews:

Brands by name

Popular brands

Airspan AirHarmony-1000, Installation Manual

Search results

Summary of Contents for AirHarmony-1000

Reviews:

Brands by name

Popular brands