manualshive.com logo in svg

Airspan AirHarmony-1000, Installation Manual

Share
Download
Airspan AirHarmony-1000 Installation Manual Download Page 44

AirHarmony-1000 Installation Guide  

UGD-D01006

 

Airspan Commercial and Internal Use 

 

37 

 

 

Figure 28: Tighten clamp bands 

 

 

6.  Mounting bracket is installed and ready for AC/DC Converter mounting. 

7.  Align the 4 mounting slots located on the flange of the AC/DC Converter with the 4 

threaded holes on the mounting bracket. 

8.  Insert the 4 pan head screws (supplied) and tighten. 

 

Figure 29: Pole mounting 

– exploded view 

 

 

5.7.2 AC/DC Converter Wall Mount Assembly 

The following images show the wall mount assembly. The converter can be fastened directly to a wall 
utilizing the holes on the unit body (4 places). 

Note:

 For the wall mount assembly the mounting bracket is 

not

 required. 

 

 

Note:

 The AC/DC converter can be mounted horizontally if required. 

 

1.  Position AC/DC Converter against the wall in close proximity to the AirHarmony-1000 so as to 

facilitate the proper connection. 

2.  Mark the wall through the holes on the AC/DC Converter at the required height. 

3.  Attach the AC/DC Converter to the wall using screws and wall plugs (x4) rated for at least 8-

10 Kg per fastener. 

 

 

Summary of Contents for AirHarmony-1000































































Reviews:

No comments

Brands by name

Popular brands

Load more brands