manualshive.com logo in svg

Airspan AirHarmony-1000, Installation Manual

Share
Download
Airspan AirHarmony-1000 Installation Manual Download Page 47

AirHarmony-1000 Installation Guide  

UGD-D01006

 

Airspan Commercial and Internal Use 

 

40 

 

 

Figure 34: Power connection - on bottom panel of AirHarmony-1000 

 

 

 

4.  Screw the gland connector plug securely into the body cavity of the unit using the provided 

Gland wrench. 

5.  Tighten the tail nut on to the body forcing the seal to compress around the power cable using 

the (provided) Gland wrench. 

 

Figure 35: Power cable assembly 

 

 

Caution:

 Do not over tighten the gland connector or the tail nut. The gland nut should be 

tightened to a torque of no more than 3.3 Nm (2.43 lb-ft) max.  

 

Note:

 When securing the cable verify there is no tension on the connector so that it is 

easy to disconnect and re-connect for future maintenance actions.  

 

Caution:

 The internal plastic parts of the mating connector are keyed. Take care to align 

these by visual inspection or by gently rotating the connector body until the key way 
sections align and the pins go in before tightening.  

 

Figure 36: Power cable attached to AirHarmony-1000 

 

 

 

Summary of Contents for AirHarmony-1000































































Reviews:

No comments

Brands by name

Popular brands

Load more brands