manualshive.com logo in svg

Airspan AirHarmony-1000, Installation Manual

Share
Download
Airspan AirHarmony-1000 Installation Manual Download Page 51

AirHarmony-1000 Installation Guide  

UGD-D01006

 

Airspan Commercial and Internal Use 

 

44 

 

 

Figure 48: Connector assembled and tightened 

 

 

6.4 Fiber Ethernet (SFP) Cable Installation 

The Fiber Ethernet Small form-factor pluggable transceiver (SFP) must be connected to the 
AirHarmony -1000 using an outdoor fiber cable. The optical connection enables a one-hand 
installation of the connector. This enables the users to easily remove and replace the SFP transceiver 
module which eliminates the need to open the unit and expose its contents to hazardous weather 
conditions. 

Note:

 Airspan recommends using the Finisar - FTLF1318P3BTL 1000BASE-LX which 

has been tested and approved by Airspan. Available from Airspan if required. 

The Outdoor fiber cable is available in 8 different lengths from 10m to 200m. 

Note:

 Airspan recommends to test the fibers 

prior to installation (using FOA’s standard 

testing industry standards). 

 

Note:

 Airspan recommends to clean the fibers according to standard procedure (using 

FOA’s cleaning guidance). 

6.4.1 SFP Cable Connection 

 

Figure 49: LC duplex cable assembly 

 

 

1.  Remove the protective dust cap from the connector housing assembled on the unit. 

2.  Line up the SFP transceiver module with the port and slide it into the port. 

3.  Connect the cable connector onto the board connector. 

 

 

Summary of Contents for AirHarmony-1000































































Reviews:

No comments

Brands by name

Popular brands

Load more brands