AIC N 100 WH Installation And Maintenance Manual Download Page 7

Fig. 1.  Data Plate - Typical

N 120 WH

EN 15502-1/EN 15502-2-1

0063CU3550

230V

/ 50Hz

12

11,8

12,9

12 - 120

11,8 - 117,1

12,9 - 127,4

0,3 kW

IPX4D

6 bar

85°C

6

B23, B23P, C13(x), C33(x), C43(x)

C53(x), C63(x), C83(x), C93(x)

Year built:

1015 19

2019

MASTER:

SLAVE:

Heat Input

Useful Output at [80°C/60°C]

Useful Output at [50°C/30°C]

Q Min. [kW]:

P Min. [kW]:

P Min. [kW]:

Q Nom. [kW]:

P Nom. [kW]:

P Nom. [kW]:

Nesta

Chrome

MODEL:

PIN:
Serial no. :

Standards:

Power Supply:
Power Consumption:
IP Class:

Max. Working Pressure [PMS]:
Max. Working Temperature:
Flue appliance type:

NOx Class:

Wall-Hung Condensing Boiler

Type:

Range rated condensing boiler

kW

120

h e a t i n g s y s t e m s

AIC Europe B.V.

Graafschap Hornelaan 163A

NL-6001 AC Weert

The Netherlands

The boiler shall be installed by a qualified installer in accordance with

provided installation and maintenance technical manual, national and

local requirements, gas safety regulations and relevant standards.

Please read installation and

maintenance manual before

installing the boiler.

The boiler is pre-adjusted in

the factory to the gas pressure

of 20mbar for gas type G20.

Gas appliance

category

Gas type

Gas appliance

pressure

Country of destination

I2E(S)

G20

20 mbar

BE

I3P

G31

37 mbar

BE

II2H3P

G20/G31

20/37/50 mbar

CH, SK

II2H3P

G20/G31

20/37 mbar

CZ, ES, GB, GR, HR, IE, IT, LT, PT, SI

II2H3P

G20/G31

20/30 mbar

RO, FI

II2E3P

G20/G31

20/50 mbar

DE

II2E3P

G20/G31

20/37 mbar

PL

II2E3P

G25/G31

20/30 mbar

RO

II2Er3P

G20/G25/G31

20/25/37 mbar

FR

I2ELL

G20/G25

20 mbar

DE

II2EK3P

G20/G25.3/G31

20/25/37 mbar

NL

EXAMPLE

G-7

Z-038791_EN • Rev A

G

eneral

 I

nformatIon

 

Package Contents 

 

î

A NESTA CHROME boiler

 

î

An Installation and Maintenance manual

 

î

A bracket and hardware for wall installation

 

î

A condensate trap (syphon), to be installed

Refer to 

“Unpacking the Product” on page 

I-26

 

for the complete unpacking and installation in-

structions.

Boiler Marking

The data plate is located at the bottom

 

of the boiler.

In addition, the S/N and appliance type are also 

available on a sticker placed inside the front face 

flap to make the information easily available if tech-

nical support is needed.

Summary of Contents for N 100 WH

















































































Reviews: