background image

  3. general

3. GENERAL

Congratulations on your purchase of this new and innovative ALMEMO

®

 simu-

lator.  It will allow you to perform a wide range of simulation runs on sensors

and transmitters and put data acquisition and automation systems into service

quickly and easily.  It also accepts signals from Pt100 and thermocouple sen-

sors, e.g. 0-10 V, 0-20 mA, and pulses and frequencies, 0-100 kHz.  With its

range of softkeys and its clear and readily understandable graphics display the

device is easy and convenient to operate.   You are nonetheless advised to

properly familiarize yourself with the way the device functions and with its nu-

merous possibilities and to carefully read these operating instructions and the

basic information on sensors in the ALMEMO

®

 Manual.  This is the best way to

avoid operating errors and prevent damage to the device.  To help you find an-

swers to your questions as quickly and easily as possible an index is provided

at the end of these instructions and at the end of the Manual.

3.1 Warranty

Each and every device, before leaving our factory, undergoes numerous qual-

ity tests. We provide a guarantee, lasting two years from delivery date, that

your   device   will   function   trouble-free.   In   the   unlikely  event   that   the   device

proves defective and you need to return it please wherever possible use the

original packaging material for dispatch and enclose a clear and informative

description of the fault and of the conditions in which it occurs. 
This guarantee will not apply in the following circumstances :

- The user attempts any form of unauthorized tampering and alteration inside the device. 
-  The device is used in environments or conditions for which it is not suited.
-  The device is used with an unsuitable power supply and / or in conjunction 

with unsuitable peripheral equipment.

-  The device is used for any purpose other than that for which it is intended.
-  The device is damaged by electrostatic discharge or lightning.
-  The user fails to observe these operating instructions 

The manufacturer reserves the right to change the product's characteristics in

the light of technical progress or to benefit from the introduction of new compo-

nents.

3.2 Standard delivery

When you unpack the device check carefully for any signs of transport damage

and ensure that delivery is complete:

Simulator ALMEMO

®

 KA 7531, ALMEMO

®

 clamp connector, test cable with

test probes, These operating instructions, ALMEMO

®

 Manual,

CD with AMR-Control software and various useful accessories 

In the event of transport damage please retain the packaging material and in-

form your supplier immediately.

 4        ALMEMO

®

 KA7531   

Summary of Contents for Almemo KA 7531





















Reviews: