manualshive.com logo in svg

Agria 5400 KL, Operating Instructions Manual, Page: 56 / 68

Share
Download
Agria 5400 KL Operating Instructions Manual Download Page 56

56

agria

 Power Mower 5400

6. Troubleshooting

W

Observe safety instructions! Have all serious malfunctions on the machine or engine repaired by your
agria workshop. They have the proper tools. Improper repairs can only add to the damage.

Problem

Possible cause

Remedy

Page

Engine-

- Spark plug connector not connected

Connect spark plug connector

does not start

-Choke is not pulled

Set Choke-lever to right position

34

- Engine-off-switch is set to “0”

Set engine-off-switch to “I”

34

-Safety circuit is not set

Set safety circuit

to start position

to start position

34

- Fuel tank empty or poor fuel

Fill fresh fuel

32

- Fuel line clogged

Clean fuel line

41

- Defective spark plug

Clean, adjust or exchange spark plug

41

- Engine too much fuel

Dry and clean spark plug and

(“flooded engine”)

start at full throttle

- Engine-off-line defective

Check line and connections

¬

- Inleaked air due to loose carburettor

Tighten fastening screws

and suction line

Misfirings

-Engine running in CHOKE range

Set CHOKE-lever to operating position

34

- Ignition cable not fixed

Fix spark plug connector on the spark plug,
fix ignition cable retaining device,
fix spark plug connector on the ignition cable

- Clogged fuel line or poor fuel

Clean fuel line,fill fresh fuel

¬

- Vent opening in fuel tank cap

Exchange fuel tank cap

clogged

- Water or dirt in fuel system

Clean fuel filter

41

Drain fuel and fill fresh fuel

- Air filter clogged

Clean air filter or exchange

39, 40

- Carburettor misadjusted

Readjust carburettor

¬

42

Excessive

-Low engine oil level

Refill oil immediately

38

temperature

-Impaired cooling

Clean cooling fan grille,
clean internal cooling fins

41

- Air filter clogged

Clean air filter or exchange

39, 40

- Carburettor misadjusted

Readjust carburettor

¬

42

Misfirings

-Short firing intervals

Adjust spark plug

41

at high speeds

- Incorrect idle mix

Adjust carburettor

¬

42

Engine frequently

- Firing interval too long,

Adjust or replace spark plug

41

stalls in idle

Defective spark plug

- Carburettor misadjusted

Readjust carburettor

¬

42

- Air filter clogged

Clean air filter

39, 40

6

6

6

6

6

6

Summary of Contents for 5400 KL





































































Reviews:

No comments