manualshive.com logo in svg

Agria 5400 KL, Operating Instructions Manual, Page: 12 / 68

Share
Download
Agria 5400 KL Operating Instructions Manual Download Page 12

12

agria

 Power Mower 5400

1

1. Safety Instructions

Weights

Always fit weights onto appropriate
weight fitting devices.

Snow clearing

Ensure snow dozer is mounted cor-
rectly! Wear slip-proof shoes.
When swivelling the snow dozer watch
out for crush and shear points. Adjust
working speed to conditions. Operator
may be injured when the mache comes
in contact with solid objects.

Maintenance

Never carry out any maintenance or
cleaning with the engine running.

Before you work on the engine, always
remove spark plug connector (petrol en-
gine only).

Check regularly and, if necessary, re-
place all protecting devices and tools
subject to wear and tear.

Replace damaged cutting tools!

Always wear safety gloves and use proper
tools when exchanging cutting tools!

Do not carry out repairs like welding,
grinding, drilling, etc. on structural and
safety-relevant parts (e.g. steering han-
dle, coupling devices)!

Keep mower and implement clean to
avoid risk of fire.

Check nuts and screws regularly for tight
fit and re-tighten, if necessary.

After maintenance and cleaning, ensure
that you reinstall all safety and protec-
tive devices and adjust them properly.

Only use original agria spare parts.

All other commercial spare parts must
correspond to quality and technical re-
quirements specified by agria.

Storage

It is not allowed to store the mower in
rooms with open heating.

Never park the mower in closed rooms
with fuel left in tank. Fuel vapours are
hazardous.

Engine, Fuel and  Oil

Never let the engine run in closed rooms.
Extreme danger of intoxication! For the
same reason, also replace damaged ex-
haust pipe immediately.

Caution with hot engine parts!

The exhaust and other engine parts
become very hot, if the engine runs and
immediately after turning off. Hold for
sufficient distance from hot surfaces and
keep children away from the running
engine.

Be careful when dealing with fuel. Great
danger of fire! Never refill fuel close to
open fire, inflammable sparks or hot en-
gine parts. Do not refill fuel in closed
rooms. Do not smoke when refilling!

Refill only with the engine switched off
and cooled down.

Do not spill any fuel, use a proper filling
device.

In case of fuel spillage, pull the power
mower away from the spillage before
you start the engine.

Make sure fuel is of specified quality.

Store fuel in approved cans only.

Store anti-corrosive agents and stabi-
lizing liquids out of reach of children. If
sickness and vomiting occur, see a doc-
tor. If fuel has contacted eyes, rinse
them thoroughly, avoid inhaling of va-
pours.

1

Summary of Contents for 5400 KL





































































Reviews:

No comments