Agria 5400 KL Operating Instructions Manual Download Page 40

Page: 40 / 68

agria

Power Mower 5400

Dry Air Filter EH 25

When You take up operation
check the air filter (E/4) on dirt,
clean it if necessary.
Clean the air filter at least every
25 operating hours or at 3-
month intervals, after some
hours in very dusty conditions:

Clean the air filter and sur-

rounding parts.

Loosen the wing nut and

take off the filter cap.

Carefully remove the foamed

preliminary filter.

Wash the foamed prelimi-

nary filter in warm lye (do not
use petrol).

Sqeeze the foamed preliminary

filter like a sponge and dry it.

Remove the filter element.

Tap the filter element against

a smooth surface.

Do not clean the foamed pre-

liminary filter and the filter ele-
ment using compressed air and
do not soak it in oil!

Reinstall the filter element and

the foamed preliminary filter.

Reposition the filter cap and

fasten the wing nut.

Replace the filter element af-

ter 5 cleaning actions or
approx. every 200 operating
hours.

Replace immediately
damaged filter elements.

5. Maintenance: 4-stroke engine

Filter paper
element

Foamed pre-filter

Filter cap

A (25 h)

Summary of Contents for 5400 KL





































































Search results

Summary of Contents for 5400 KL

Reviews:

Agria 5400 KL, Operating Instructions Manual, Page: 40 / 68

Search results

Summary of Contents for 5400 KL

Reviews: