Agria 5400 KL Operating Instructions Manual Download Page 24 | Manualshive

Page: 24 / 68

Agria 5400 KL Operating Instructions Manual Download Page 24

24

agria

Power Mower 5400

3

3. Devices and Operating Elements

Steering Handle Height
Adjustment

W

Do never adjust operating

handles during working
– risk of accidents!

l

Unfix ball handle levers

on either

side until the detents

are free.

l

Bring left and right steering handle to

the desired height and introduce into the
respective detent.

l

Tighten ball handle levers

again.

Eyelet for Loading

For transport facilities and for fixing

the security rope when working on
slopes, the power mower 5400 is
equipped with a hook (A/3) and the 5400
KL with an ring (C/3).

Do not use any loading devices with
sharp edges (e.g. sharp-edged hooks,
eyelets etc.).

Never walk or remain
under moving loads.
Danger!

Fixing Points

For towing away, recovering and ty-

ing down and to ensure a safe trans-
port, use the

fixing points

at the hook (A/3) or eyelet (C/3) and engine
food guard.

A/3

C/3

5400 KL

5400

«
...
22
23
24
25
26
...
»

Summary of Contents for 5400 KL





































































Reviews:

No comments