manualshive.com logo in svg

Agria 5400 KL, Operating Instructions Manual, Page: 53 / 68

Share
Download
Agria 5400 KL Operating Instructions Manual Download Page 53

agria

 Power Mower 5400

53

5. Maintenance

Storage

For longer periods of no operation:

a) Clean thoroughly
Repair paint coat

b) Spray all shining parts, in particu-
lar cutter bar, with Bio-slushing oil.

c) Engine preservation

l

Drain fuel completely or fill the fuel

tank, add fuel stabilizer (agria No. 799
09) to the fuel tank - observe instruc-
tions.
Operate the engine for approx. 1 minute.

l

Change the engine oil.

l

Fill a teaspoon of engine oil (approx.

0.03l) into the spark plug opening.
Slowly crank the engine.

l

Reinstall the spark plug and set the

valves on compression using the recoil
starter (pull the starter rope until you feel
resistance), the valves are closed.

l

 Crank the engine slowly at 2–3 week

intervals (spark plug connector is re-
moved!) and set the valves on compres-
sion again.

d) Drive-wheels

Support drive-wheels in such a way that

tyres have no
ground contact.
Pneumatic tyres are
quickly destroyed, if
left standing under
load and uninflated.

e) Clutch

Always park mower with hand clutch le-

ver pulled (pawl
locked in place).
Otherwise, clutch
problems may result
due to corrosion.

f) Storing the machine

To avoid severe corrosion:

- to preserve the machine from atmos-
pheric influences

Do not park the ma-
chine in:

- humid rooms

- in rooms where
fertilizer is stored

- in stables or adja-
cent rooms.

g) Protect machine

with cloth or a simi-
lar cover.

5

5

Summary of Contents for 5400 KL





































































Reviews:

No comments