manualshive.com logo in svg

Agria 5400 KL, Operating Instructions Manual, Page: 51 / 68

Share
Download
Agria 5400 KL Operating Instructions Manual Download Page 51

agria

 Power Mower 5400

51

5

5

5

5. Maintenance

Cutter Bar

W

Stop the engine, remove the
 spark plug connector!

Wear safety gloves!

W

Always attach the knife guard
before laying the mowing

knife aside!

Bottom knife ESM
universal-municipal-
cutter bar

Top knife

Correct
grinding

Wrong
grinding

Regrinding the Mowing Knives

Wear safety goggles and

safety gloves.

After 4–20 operating hours, depend-
ing on the strain the mowing knives are
exposed to, they become blunted and
regrinding is necessary.

For this purpose, we recommend to use
a hand grinder of 15,000 to 20,000 rpm
with a pot-shaped grinding pin of 25 mm
in diameter and approx. 35 mm in length
or a special grinding tool.

I

Grinding of mowing knives is
essential for clean and smooth
mowing.

l

For grinding, use front of grinding pin

and slide it from knife back to blade tip.

l

Blades must not heat up. They are

destroyed when they turn blue (glowed
out and soft).

l

Do not round-off the tips of the blades

(P).

l

Do not grind the blades in a bow (P)

l

Remove any burr with a hand grind-

ing stone.

I

For mounting or dismounting
the mowing knifes  as well as for

the maintenance of the cutter bar re-
fer to

  operating instructions

cutter bar

5

Summary of Contents for 5400 KL





































































Reviews:

No comments