manualshive.com logo in svg

Agria 3600 075, Translation Of The Original Operating Instructions, Page: 49 / 76

Share
Download
Agria 3600 075 Translation Of The Original Operating Instructions Download Page 49

4 Commissioning and Operation 

Two-wheel tractor 

agria 3600

 

49 

  Never leave the machine unattended 

while the engine is running. 

If you have to clean the machine during work, 
switch off the engine and remove sparking-plug 
connector(s) and ignition key for safety reasons. 

Working on slopes 

Observe the operating instructions of the 
implements and the safety instructions. 

Slope capability 

±

max.

 = 20° (37%), see page 21 

  Depending on the type of ground sur-

face (vegetation, humidity ...), wear suitable 
shoes so that you do not slip or fall. 

If there is a risk of instability on a slope, have a 
second person who holds the machine with a bar 
or a rope. The second person must stand above 
the machine at a safe distance from the hazard 
zone. 

Work across the slope along contour lines if 
possible. If possible, turn the machine in uphill 
direction. 

Starting the engine on a slope 

Use the following procedure if you have to re-
start a stalled engine: 

•

Leave PTO shaft and gearbox engaged; 
braking effect

•

Set the safety circuit to "Stop" position

•

Restart the engine

  

Summary of Contents for 3600 075













































































Reviews:

No comments