Agria 3600 075 Translation Of The Original Operating Instructions Download Page 9 | Manualshive

Page: 9 / 76

Agria 3600 075 Translation Of The Original Operating Instructions Download Page 9

Two-wheel tractor

agria 3600

9

The engine is filled with gear oil when it is deliv-
ered. To prevent oil from leaking during the
transport, a plug is installed instead of the oil
dipstick. Replace the plug with the oil dipstick.
See figure.

The machine tyres are not contained in the cardboard box. They are

delivered separately. Combine only tyres that are approved in the Agria sales
list.

Version 3600 (2+2): Rigid hexagonal wheel shaft

•

Installing the driving wheels:

- 4.00-8:

Install the driving wheels with wheel bolts and washers to the wheel flang-

es. Slip them on the hexagonal wheel shaft such that the arrow-shaped tyre pattern
points in the driving direction. Insert the lynch pin through the wheel hub and shaft
bore, and close the lynch pin.

- 4.00-10:

Screw the wheel adapter flanges on the driving wheels. Install the driving

wheels with the wheel bolts and washers on the wheel flanges. Slip them on the
hexagonal wheel shaft such that the arrow-shaped tyre pattern points in the driving
direction. Insert the lynch pin through the wheel hub and shaft bore, and close the
lynch pins.

«
...
7
8
9
10
11
...
»

Summary of Contents for 3600 075













































































Reviews:

No comments