manualshive.com logo in svg

Agria 3600 075, Translation Of The Original Operating Instructions, Page: 35 / 76

Share
Download
Agria 3600 075 Translation Of The Original Operating Instructions Download Page 35

3 Devices and Operating Elements 

Two-wheel tractor 

agria 3600

 

35 

Snow chains 

Observe the manufacturer's instructions when you use snow chains. Ensure that 
there is enough clearance at the machine components. 

Front and wheel ballast 

Front ballast and wheel ballast can be added to improve the traction power. 

Attachment front ballast:

 Part no. 3628 011 

Attachment wheel ballast:

 Part no. 3621 011 

3600 (2+2): Hexagonal wheel shaft 

•

Unscrew the driving wheels.

•

Install the wheel hubs (1) such that the hex-
agonal tube point inwards. First, screw on 
the driving wheels with the long hexagon 
head screws (2) [included in the scope of 
delivery of the wheel ballast]. For each 
wheel, install 2 diagonally opposite screws 
from the inside to the wheel flange (1).

•

For each wheel, install 2 diagonally opposite 
wheel bolts (4) from the inside in the empty 
threaded holes of the wheel flange.

•

Using 2 long special nuts (7) and washers 
(6), screw the wheel ballast elements diago-
nally on the hexagon head screws (2) you 
screwed in from the inside.

•

Tighten wheel bolts and ballast fastening 
nuts with 

50 Nm

.

3600 (3+2) wheel flange with stud bolts 

•

At each wheel, unscrew 2 diagonally oppo-
site wheel nuts with washers.

•

Using 2 long special nuts (7) and washers 
(6), screw the wheel ballast elements diago-
nally on the stud bolts (8).

•

Tighten wheel nuts and  ballast fastening 
nuts with 

50 Nm

.

Summary of Contents for 3600 075













































































Reviews:

No comments