manualshive.com logo in svg

Agria 3600 075, Translation Of The Original Operating Instructions, Page: 62 / 76

Share
Download
Agria 3600 075 Translation Of The Original Operating Instructions Download Page 62

5 Maintenance and Repair 

 

 

62 

Two-wheel tractor 

agria 3600

 

General 

 

  

Before each start-up check for escaping fuel and 
oil and eliminate the cause. 

- agria-Service - 

  

 

  

Regularly check nuts and bolts for tightness and 
retighten if necessary. 

  

 

  

At least 

yearly

 and after cleaning: 

Lubricate all sliding or moving parts (such as 
speed regulating lever, hand lever bearing, etc.) 
with bio lubricating grease or bio lubricating oil. 

  

Cleaning 

 

  

 

  

Machine 

Clean thoroughly with water immediately after 
each use. 

Do not expose electric cables and components 
to direct water jets. 

Then lubricate all sliding parts with bio-
lubricating oil or grease with bio-lubricating 
grease. 

 

In addition lubricate the lubrication points on the 
machine immediately after cleaning with a high 
pressure cleaner, and  put the machine briefly 
into operation to press out the penetrated water. 

To protect the bearings against penetrating dirt, 
sap and water, there shall be a grease collar at 
the bearing points. 

 

  

Engine 

Only clean the engine with a cloth. Do not spray 
with water, as water could enter the ignition and 
fuel system and cause malfunctions. 

  

Summary of Contents for 3600 075













































































Reviews:

No comments