manualshive.com logo in svg

Agria 3600 075, Translation Of The Original Operating Instructions, Page: 34 / 76

Share
Download
Agria 3600 075 Translation Of The Original Operating Instructions Download Page 34

3 Devices and Operating Elements 

34 

Two-wheel tractor 

agria 3600

 

3600 (3+2) 

with driving wheels 4.00-8 

3600 (3+2)  

with driving wheels 4.00-10 

1 Wheel flange 

2 Wheel adapter flange 

3 Washer 

4 Wheel nut 

5 Hexagon head screw 

6 Driving wheel 

7 Washer 

8 Wheel nut 

Version 3600 (3+2) 

= wheel flange with stud bolts 

The corresponding driving wheels (6) are in-
stalled on the wheel flanges with wheel nuts (5). 

First install the wheel adapter flanges (2) to the 
driving wheels when you use driving wheels 
4.00-10. 

The required wheel track can be achieved with 
the installation of the driving wheels to the wheel 
flanges or the wheel adapter flanges (flanges / 
wheels turned inward or outward, and mounted 
from the inside or the outside to the wheel 
adapter flanges). (Track plan see page 19). 

Install the driving wheels such that the tip of the 
tyre pattern points in driving direction (seen from 
above). This provides full traction power. This 
must also be taken into account when the steer-
ing bar is rotated through 180° for front imple-
ment attachment. 

Wheel mounting bolts 

3600 (2+2):

 Wheel bolts with washers. 

3600 (3+2):

  Stud bolts with washers  and wheel 

nuts 

With a new machine and after each wheel 
change tighten the wheel bolts or wheel nuts 
after the first 

2

 operating hours with 

50 Nm

, and 

always during maintenance work. 

Driving wheel utilization 

Size 

Tyre pattern 

Utilization 

Part no. 

4.00-8 

Field profile 

Tilling, ridging, 

mowing, sweep-
ing, 

winter service 

3690 011 

4.00-10 

Field profile 

Ploughing, tilling 

3690 021 

Summary of Contents for 3600 075













































































Reviews:

No comments