Agria 3600 075 Translation Of The Original Operating Instructions Download Page 45 | Manualshive

Page: 45 / 76

Agria 3600 075 Translation Of The Original Operating Instructions Download Page 45

4 Commissioning and Operation

Two-wheel tractor

agria 3600

45

Starting the petrol engine

Never start or allow the engine to run in

enclosed rooms or rooms that are not venti-
lated.

It is essential to ensure for sufficient ventila-
tion and a quick extraction of the exhaust
fumes. The exhaust fumes contain carbon
monoxide that is highly toxic when inhaled.

Plug on the sparking-plug connector

1.

Open the fuel cock (C/13)

2.

Cold

engine: Set CHOKE actuator (C/5) to

"CHOKE". Reset CHOKE when the engine is
hot

Engine

at operating temperature

: Leave

CHOKE in normal operating position

3.

Switch gear and PTO shifting to ("

O

")

4.

Set engine stop switch (B/4) to operating
position ("

ON

")

5.

Set speed regulating lever (B/3) to approxi-
mately 1/3 throttle

6.

Start the engine from outside the hazard
zone:
Hold the starter rope at the starter handle
(C/7) and pull it out

vigorously

and

rapidly

to start the engine. Guide the handle back af-
ter the engine has started. Do not allow it to
shoot back.

7.

Once the engine is running, set the engine
speed to min and allow the engine to warm
up for a short time. Slowly move the choke
actuator back to operating position (if actuat-
ed).

«
...
43
44
45
46
47
...
»

Summary of Contents for 3600 075













































































Reviews:

No comments