manualshive.com logo in svg

Agria 3600 075, Translation Of The Original Operating Instructions, Page: 21 / 76

Share
Download
Agria 3600 075 Translation Of The Original Operating Instructions Download Page 21

2 Technical Data 

 

 

Two-wheel tractor 

agria 3600

 

21 

Petrol engine 

Engine make:

 .................................................................................................. Honda 

Type:

 ............................................................................................................... GX160 

Bore x stroke:

 ......................................................................................... 68 x 45 mm 

Displacement:

 .............................................................................................. 163 cm

3

 

Net output:

 ........................................................... 3.6 kW (4.9 DIN-PS) at 3600 min

-1

 

Torque:

 ................................................................................... 10.3 Nm at 2500 min

-1

 

Design:

 ............................................... air-cooled 1-cylinder four-stroke petrol engine 

Working speed:

 ........................................................................................ 3600 min

-1

 

Idle speed:

 ....................................................................................... 1250-1600 min

-1

 

Spark plug:

 ......................................................................................... NGK BPR6ES 

Electrode gap: 0.7-0.8 mm 

Starting device:

 ............................................................................... cable-pull starter 

Fuel:

 ....................................................................... commercially available car petrol 

octane number see engine operating instructions 

Fuel consumption:

 ................................................................................... 313 g/kWh 

Capacity of the fuel tank:

 .................................................................................. 3.1 l 

Air filter:

 .................................................................................................. oil bath type 

Engine oil:

 .................................................................. fill volume approximately 0.6 l 

 

Multigrade oil SAE 10W-30, quality class API-SJ or higher 

Slope suitability:

 ................................................................................... < 20° (37 %) 

  

Summary of Contents for 3600 075













































































Reviews:

No comments