Agora Models LONDON TRANSPORT ROUTEMASTER RM 857 Build Instructions Download

Page: 52 / 55

Take the exhaust pipe

30C

and identify the fixing points (circled

in red) for the exhaust pipe. The hole on the end of the pipe goes

through a hole in the cross member of the frame

16A

and fits over the

screw hole in part

30A

. The hole near the elbow of the exhaust fits

over the screw hole at the back of the subframe. Fix in place with one

screw and one

screw, as shown in the inset, right.

NOTE:

Support part

30A

from below while you fix it in place.

STEP BY

STEP

Take the silencer top

30A

and the subframe

assembly. Work on the
underside, supporting the
frame carefully and taking
care not to rest the assembly
on any engine parts. Identify
the two holes in the rear part
of the frame

16A

(circled in

red). Position the two screw
eyes on the side of part

30A

over the screw sockets in the
frame. Fix in place with two

screws. The image below

shows part

30A

fixed in place.

16A

30C

30A

30C

16A

AGORA

MODELS

AGORA

MODELS

RM 857

Summary of Contents for LONDON TRANSPORT ROUTEMASTER RM 857
























































Search results

Summary of Contents for LONDON TRANSPORT ROUTEMASTER RM 857

Reviews:

Related manuals for LONDON TRANSPORT ROUTEMASTER RM 857

Brands by name

Popular brands

Agora Models LONDON TRANSPORT ROUTEMASTER RM 857, Build Instructions

Search results

Summary of Contents for LONDON TRANSPORT ROUTEMASTER RM 857

Reviews:

Related manuals for LONDON TRANSPORT ROUTEMASTER RM 857

Brands by name

Popular brands