Agora Models LONDON TRANSPORT ROUTEMASTER RM 857 Build Instructions Download

Page: 49 / 55

Take the beam

29V

and fit

it across the two front beams

of the sub-frame,

27A

and

27B

, in front

of the engine assembly but behind the fan.

Ensure the screw holes in

29V

are over the

holes in the beams.

NOTE:

The screw holes fit

over the second holes in the beams, not the end

ones. Fix in place with two

screws. The inset

below left shows the beam fixed in place.

Carefully turn the assembly on to its side so that you can

fix the engine in place through the holes in part

27D

(see

previous step). Support the assembly and engine while you

fix it in place with two

screws see inset below).

Mount the radiator assembly on the
front of beams

27A

and

27B

using the

mounting brackets

28H

. At the same time, guide

the peg on the end of the thermostat pipe

28A

into

the top socket on the radiator (as indicated in red).
Ensure the fan

26D

fits into the fan ring on the back

of the radiator. Fix in place with two

screws. The

inset below shows the radiator fixed in place.

Study the

diagram carefully

and note the position

of the front of the

engine in relation to

the beam 29V.

27B

27A

27D

29V

27B

28A

27A

28H

AGORA

MODELS

AGORA

MODELS

RM 857

Summary of Contents for LONDON TRANSPORT ROUTEMASTER RM 857
























































Search results

Summary of Contents for LONDON TRANSPORT ROUTEMASTER RM 857

Reviews:

Related manuals for LONDON TRANSPORT ROUTEMASTER RM 857

Brands by name

Popular brands

Agora Models LONDON TRANSPORT ROUTEMASTER RM 857, Build Instructions

Search results

Summary of Contents for LONDON TRANSPORT ROUTEMASTER RM 857

Reviews:

Related manuals for LONDON TRANSPORT ROUTEMASTER RM 857

Brands by name

Popular brands