Agora Models LONDON TRANSPORT ROUTEMASTER RM 857 Build Instructions Download

Page: 48 / 55

Take the drive shaft

23I

, supplied with stage 23, and

the subframe assembly completed in stage 27. Check

the difference between the ends of part

23I

, and ensure you

have it the right way round. Working from below, fit one end
under the notch in the cross bar on the rear sub-frame

17A

and into the socket on the pulley part

22D

. The other end goes

under the cross rod

27D

. The shaft rests on the notch in the

narrow cross bar on part

17A

. (inset, right).

Turn the assembly the right way
up to fit the engine to the sub-

frame. Fit the free end of the drive shaft

23I

into the flywheel

25N

. Two sockets

on the underside of the engine assembly
fit over the eyelets on the subframe (as
shown by red dotted lines, and below,
viewed from underneath).

22D

23I

27D

17A

25A

25N

23I

27D

AGORA

MODELS

RM 857

Summary of Contents for LONDON TRANSPORT ROUTEMASTER RM 857
























































Search results

Summary of Contents for LONDON TRANSPORT ROUTEMASTER RM 857

Reviews:

Related manuals for LONDON TRANSPORT ROUTEMASTER RM 857

Brands by name

Popular brands

Agora Models LONDON TRANSPORT ROUTEMASTER RM 857, Build Instructions

Search results

Summary of Contents for LONDON TRANSPORT ROUTEMASTER RM 857

Reviews:

Related manuals for LONDON TRANSPORT ROUTEMASTER RM 857

Brands by name

Popular brands