Agora Models LONDON TRANSPORT ROUTEMASTER RM 857 Build Instructions Download

Page: 14 / 55

Turn the frame over and identify
the fixing points for the tank,

circled in inset, top. Fix the tank in
place, using two

screws.

NOTE:

The screws go through the eyelets

on the side of the tank and into the
sockets on the side of the frame

17A

The inset (right) shows the tank in
place.

On the underside of the chassis frame,
identify the fixing point on the control

lever

13I

(circled, top inset) for the connector

23A

. Slot the ends of the connector over the

eyelet in part

13I

NOTE:

The larger eyelet of

part

23A

is uppermost as you work. Support

part

13I

, which is quite delicate, while you fix

the connector in place with a

screw. The

inset on the right shows part

23A

in place.

23B

17A

23A

13I

23A

AGORA

MODELS

RM 857

Summary of Contents for LONDON TRANSPORT ROUTEMASTER RM 857
























































Search results

Summary of Contents for LONDON TRANSPORT ROUTEMASTER RM 857

Reviews:

Related manuals for LONDON TRANSPORT ROUTEMASTER RM 857

Brands by name

Popular brands

Agora Models LONDON TRANSPORT ROUTEMASTER RM 857, Build Instructions

Search results

Summary of Contents for LONDON TRANSPORT ROUTEMASTER RM 857

Reviews:

Related manuals for LONDON TRANSPORT ROUTEMASTER RM 857

Brands by name

Popular brands