Agora Models LONDON TRANSPORT ROUTEMASTER RM 857 Page 32 Build Instructions Download

Page: 32 / 55

KEY TO PARTS SUPPLIED

27A

Left beam

27B

Right beam

27C

Steering bar

27D

Cross rod

27E

Left mounting

27F

Right mounting

1.7 x 3mm (x2)

2.3 x 4mm (x21)

1.5 x 4mm (x9)

1.7 x 4mm (x2)

Take the right beam

27B

and identify the fixing point

for the steering bar

27C

(circled). Fix in place with an

screw.

Fit the right
mounting

27F

the right beam

27B

and

fix in place with two

screws. Repeat to fit the
left mounting

27E

the left beam

27A

(inset,

above).

STAGE 27

FITTING THE FRONT SUBFRAME AND

FRONT AXLE

The beams of the front part of the subframe are fitted to the

rear subframe. The front axle is fitted between the beams of

the front subframe.

27A

27B

27C

27D

27F

27E

27B

27F

27C

27B

27A

27E

AGORA

MODELS

AGORA

MODELS

RM 857

Summary of Contents for LONDON TRANSPORT ROUTEMASTER RM 857
























































Search results

Summary of Contents for LONDON TRANSPORT ROUTEMASTER RM 857

Reviews:

Related manuals for LONDON TRANSPORT ROUTEMASTER RM 857

Brands by name

Popular brands

Agora Models LONDON TRANSPORT ROUTEMASTER RM 857, Build Instructions

Search results

Summary of Contents for LONDON TRANSPORT ROUTEMASTER RM 857

Reviews:

Related manuals for LONDON TRANSPORT ROUTEMASTER RM 857

Brands by name

Popular brands