manualshive.com logo in svg

Agilent Technologies E8364-60105, Installation Note, Page: 3 / 37

Share
Download
Agilent Technologies E8364-60105 Installation Note Download Page 3

Installation Note E8364-90022                                                                                                                         

 

3

Contacting Agilent

Assistance with test and measurements needs and information on finding a local Agilent 
office are available on the Web at:

www.agilent.com/find/assist

NOTE

 In any correspondence or telephone conversation, refer to the Agilent 
product by its model number and full serial number. With this 
information, the Agilent representative can determine whether your 
product is still within its warranty period.

If you do not have access to the Internet, please contact your Agilent field engineer.

About the Upgrade Kit

If you need assistance, refer to 

“Contacting Agilent” on page 3

.

Description of the Upgrade

This upgrade kit is used to extend the frequency range of the:

• E8364B/C PNA microwave network analyzer from 50 GHz to 67 GHz

This upgrade applies only to a standard PNA, with no optional hardware.

Products affected . . . . . . . . . . . . . . . . . . . . . . . . . . E8364B/C with no RF hardware options

Installation to be performed by  . . . . . . . . . . . . . . Agilent service center or personnel 

qualified by Agilent

Estimated installation time . . . . . . . . . . . . . . . . . 2.5 hours

Estimated adjustment time  . . . . . . . . . . . . . . . . . 1 hour

Estimated full instrument calibration time  . . . . 4.5 hours

Summary of Contents for E8364-60105






































Reviews:

No comments