manualshive.com logo in svg

Agilent Technologies E8364-60105, Installation Note, Page: 15 / 37

Share
Download
Agilent Technologies E8364-60105 Installation Note Download Page 15

Installation Note E8364-90022                                                                                                                         

 

15

Step 6. Remove the Old Bottom Side Hardware and Cables

•

Remove the A17 LOMA 10

•

Remove the A18 MA 20

•

Remove the A22 Switch/Splitter

•

Remove the A23 and A24 Detectors

•

Remove the A27, A28, A29, and A30 First Converters (Mixers)

•

Remove the A25 and A26 Test Port Couplers

Remove the A17 LOMA 10

1. Using a 5/16-inch wrench, disconnect the three semirigid cables (item 

①

) from the A17 

LOMA 10. Two of these cables should already be disconnected (from step 4).

2. Disconnect the ribbon cable (item 

②

) at the A17 LOMA 10.

3. Using a T-10 TORX driver, remove the four mounting screws (item 

③

) from the side of the 

analyzer. Retain the mounting screws for reinstallation later.

CAUTION

Be careful not to damage the center pins of the semirigid cables. Some flexing of 
the cables is necessary to remove the assembly. Do not over-bend them.

4. Remove the A17 LOMA 10 from the analyzer. Observe the 

CAUTION

 above.

Figure 7

A17 LOMA 10 Removal

Summary of Contents for E8364-60105






































Reviews:

No comments