manualshive.com logo in svg

Agilent Technologies E8364-60105, Installation Note, Page: 21 / 37

Share
Download
Agilent Technologies E8364-60105 Installation Note Download Page 21

Installation Note E8364-90022                                                                                                                         

 

21

Step 7. Install the New Hardware and Cables

•

Install the New A17 LOMA 12

•

Install the New A18 MA 24

•

Install the New A25 and A26 Test Port Couplers

•

Install the New A23 and A24 SOMA 70s

•

Install the New A22 Switch

•

Install the New A27, A28, A29, and A30 First Converters (Mixers)

•

Install the New Cables

Install the New A17 LOMA 12

1. Position the new A17 LOMA 12 in the analyzer as shown. Observe the 

CAUTION

 below.

CAUTION

Be careful not to damage the center pins of the semirigid cables. Some flexing of 
the cables is necessary when installing the assembly. Do not over-bend them. 

2. Using a T-10 TORX driver, install three of the four mounting screws (item 

③

), previously 

removed from the old A17 LOMA 10, through the side of the analyzer as shown. One of the 
screws removed previously is not reused.

3. Using a 5/16-inch torque wrench (set to 10 in-lbs), reconnect the two semirigid cables 

(item

①

) to the A17 LOMA 12. Observe the 

CAUTION

 above.

4. Reconnect the ribbon cable (item 

②

) to the A17 LOMA 12.

Figure 13

A17 LOMA 12 Installation

Summary of Contents for E8364-60105






































Reviews:

No comments