Agilent Technologies 81610A User Manual Download Page 106

Page: 106 / 118

How to clean instruments with an optical glass plate

Cleaning Information

Agilent 81610A/11A/12A/13A/14A Return Loss Module, Fifth Edition

103

If there are fluids or fat in the connector, please refer the instrument

to the skilled personnel of Agilent’s service team.

C A U T I O N

Only use clean, dry compressed air. Make sure that the air is free of

dust, water, and oil. If the air that you use is not clean and dry, this

can lead to filmy deposits or scratches on the surface of your

connector interface. This will degrade the performance of your

transmission system.

Never try to open the instrument and clean the optical block by

yourself, because it is easy to scratch optical components, and cause

them to become misaligned.

How to clean instruments with
an optical glass plate

Some instruments, for example, the optical heads from Agilent

Technologies have an optical glass plate to protect the sensor. Clean

this glass plate in the same way as optical lenses (see

“How to clean

lenses” on page 102

How to clean instruments with a
physical contact interface

Remove any connector interfaces from the optical output of the

instrument before you begin the cleaning procedure.

Cleaning interfaces is difficult as the core diameter of a single-mode

fiber is only about 9

m. This generally means you cannot see streaks

or scratches on the surface. To be certain of the degree of pollution on

the surface of your interface and to check whether it has been

removed after cleaning, you need a microscope.

Summary of Contents for 81610A























































































































Search results

Summary of Contents for 81610A

Reviews:

Agilent Technologies 81610A, User Manual, Page: 106 / 118

Search results

Summary of Contents for 81610A

Reviews: